Bloc moteur reconditionné pour base FORD 5.8 litres GT40

Caractéristiques :

- Culasses GT40 - 300HP

- Perçage pour pompe à essence mécanique

Le reconditionnement moteur intègre la rectification, l'usinage, le remplacement et le contrôle de l'ensemble des éléments clefs afin de vous fournir un bloc moteur marin apte à remplacer votre ancienne mécanique.

Moteur incluant des pièces internes de qualités supérieur afin de répondre aux exigences marines.

The Suzuki DF6A outboard is a 4-stroke single-cylinder engine with a cylinder capacity of no less than 138 cm3.

Its excellent half-regime couple, combined with its low weight, allows accelerations of a rare quality.His system CDI offers great precision to ignition, which allows to optimize its performance.It also incorporates security that will prevent any risk of overregime.

The design of the frank bar allows the most comfortable use position possible and a better weight distribution.Note a few other main features of this light engine that has a power selector (before, neutral, rear) a girth of 180° (for excellent manuvrability), as well as a large transport handle.

Tree or rear panel length:

- S:381mm

- L:508mm

Dry weight with no propeller or oil battery cable:

- S: 23.5 Kg

- L: 24.5 Kg

Manual start, straight bar, front/neutre/rear.

Attention for transport, the motor is delivered without oil in the crankcase, it is essential to make the oil recommended by the manufacturer in order to put in service the motor: recommended engine oil, Motul 10W40 - 4 time - 2 Litres

The manufacturer's warranty could not apply if this operation was not performed.

Pack moteur complet PCM ZR409.

Montage non catalysé avec ou sans transmission selon disponibilité usine.

Pour plus d'informations merci de nous contacter

Power pack Mercruiser reconditioned 383 MPI 350HP for mounting in Mercruiser base.

All SÉRIE-PLUS engines are fully reused to nine.This is an original Mercury Marine OEM piece that includes exhaust collectors, electrical and ignition systems, so that it is ready to be installed directly in a boat.

This 350HP engine features a 261 Kilowatts at the wheel with a maximum speed (WOT) of 4800-5200 and a compression ratio:9.0:1.

The recommended oil is Mercury MerCruiser Synthetic Blend 25W-40, classified NMMA FC-W with a tolerance to fuel and ethanol: 87 octane / up to 10% ethanol.

Motor systems MerCruiser 383 MPI 350HP for mounting in base:

- Engine control: ECM 555 with cliquetis control and vilebrequin activation,

- Fuel supply: GEN II Cool Fuel with overpower pump,

- Fuel injection: Multipoint electronic injection (MPI),

- Admission: Long channel admission in two parts with 75 mm butterfly body,

- Escape: Hot iron collector coated with electrodeposition paint with dry seam elbow,

- Water drain: Multi-point copper,

-Accessories training: snake belt,

- Lubrication: 100 psi high-speed oil pump.

Mercury Remanufacturing engines have a one-year limited factory warranty.

6-litre bobtail engine pack without direct sea water cooler without catalysts.

Reconditioned engine block GM496 8.1 litres no HO.

This type of block being not on stock in contrast to HO bases please contact us directly for any information.

Perfect product for replacing your Mercruiser engine, Volvo penta

The engine reconditioning incorporates the rectification, machining, replacement and control of all key elements to provide you with a marine engine block that can replace your old mechanics.

Reconditioned engine block after 1990 for GM V8 7.4 litres base

Characteristics :

- Rear spi of vilebrequin in one piece

- GM454 generation VI engine base

- oval intake passages

- Standard rotation: ignition 1-8-4-3-6-5-7-2

- Rollers

- 4 bolts per vilebrequin bearings

- 6 fixing screws for distribution.

- Culasses with central drilling in the middle of the admission (NON L29)

We usually replace MARK V motor bases with flat pushers by MARK VI roller pushers.

Perfect product for replacing your Mercruiser engine, Volvo, Crusader.

The engine reconditioning incorporates the rectification, machining, replacement and control of all key elements to provide you with a marine engine block that can replace your old mechanics.

Bloc moteur reconditionné en rotation standard LH avant 1990 pour base GM V8 7.4 litres

Caractéristiques :

- Joint spi arrière de vilebrequin en 2 morceaux

- Base moteur GM454 génération IV

- Passages d'admission ovales

- Kit de distribution disposant d'une chaine

- Ordre d'allumage : 1-8-4-3-6-5-7-2

- Perçage pour l'axe de la pompe à essence

Moteur incluant :

- Cache culbuteurs ( aluminium type G6 )

- Carter d'huile en tôle

- Carter de distribution

- Damper avant

- Joints d'admission et d'échappement

Produit parfait pour le remplacement de votre moteur Crusader , Chriscraft , RIVA ...

Le reconditionnement moteur intègre la rectification, l'usinage, le remplacement et le contrôle de l'ensemble des éléments clefs afin de vous fournir un bloc moteur marin apte à remplacer votre ancienne mécanique.

Moteur incluant des pièces internes de qualités supérieur afin de répondre aux exigences marines.

Reconditioned engine block for base FORD 5.8 litres.

Characteristics :

- Flat powders

- Ignition order: 1-3-7-2-6-5-4-8

- Rear spi of vilebrequin in one piece

- Block Windsor casting # D4 - D9

- Drilling for mechanical gas pump

Perfect product for the replacement of your WTO engine, VOLVO, PCM ...

The engine reconditioning incorporates the rectification, machining, replacement and control of all key elements to provide you with a marine engine block that can replace your old mechanics.

Reconditioned engine block for base FORD 5.8 litres in reverse rotation

Characteristics :

- Flat powders

- Ignition order: 1-8-4-5-6-2-7-3

- Rear spi of vilebrequin in one piece

- Block Windsor casting # D4 - D9

- Drilling for mechanical gas pump

Perfect product for replacing your PCM engine, Indmar ...

The engine reconditioning incorporates the rectification, machining, replacement and control of all key elements to provide you with a marine engine block that can replace your old mechanics.

Vortec reconditioned engine block for GM V8 5.7 liters with 8 attachment screws for the intake pipe.

Characteristics :

- Rear spi of vilebrequin in one piece

- 8 attachment screws for intake pipe

- Cache culbuteurs fixation centre

- Standard rotation: ignition 1-8-4-3-6-5-7-2

-No drilling for the gas pump axis

- VORTEC types

Perfect product for replacing your Crusader, Mercruiser, Volvo, WTO ...

The engine reconditioning incorporates the rectification, machining, replacement and control of all key elements to provide you with a marine engine block that can replace your old mechanics.

Reconditioned motor block LH after 1990 for GM V8 5.7 liters with 12 attachment screws for the intake pipe.

Characteristics :

- Rear spi of vilebrequin in one piece

- 12 attachment screws for intake pipe

- Cache culbuteurs fixation centre

- Standard rotation: ignition 1-8-4-3-6-5-7-2

- drilling for the gas pump axis

Perfect product for replacing your Crusader, Mercruiser, Volvo, WTO ...

The engine reconditioning incorporates the rectification, machining, replacement and control of all key elements to provide you with a marine engine block that can replace your old mechanics.

Repacked motor block in standard LH rotation before 1990 for base GM V8 5.7 litres with 12 attachment screws for intake pipe.

Characteristics :

- Rear spi of vilebrequin in 2 pieces

- 12 attachment screws for intake pipe

- Cache asbuteurs fixation extérieur

- Standard rotation: ignition 1-8-4-3-6-5-7-2

- drilling for the gas pump axis

Perfect product for replacing your Crusader, Mercruiser, Volvo, WTO ...

The engine reconditioning incorporates the rectification, machining, replacement and control of all key elements to provide you with a marine engine block that can replace your old mechanics.

Reconditioned Vortec motor block for GM V8 5 litres base with 8 attachment screws for intake pipe.

Characteristics :

- Rear spi of vilebrequin in one piece

- 8 attachment screws for intake pipe

- Cache culbuteurs fixation centre

- Standard rotation: ignition 1-8-4-3-6-5-7-2

-No drilling for the gas pump axis

- VORTEC types

Perfect product for replacing your Crusader, Mercruiser, Volvo, WTO ...

The engine reconditioning incorporates the rectification, machining, replacement and control of all key elements to provide you with a marine engine block that can replace your old mechanics.

Repacked motor block LH after 1990 for base GM V8 5 litres with 12 attachment screws for the intake pipe.

Characteristics :

- Rear spi of vilebrequin in one piece

- 12 attachment screws for intake pipe

- Cache culbuteurs fixation centre

- Standard rotation: ignition 1-8-4-3-6-5-7-2

- drilling for the gas pump axis

Perfect product for replacing your Crusader, Mercruiser, Volvo, WTO ...

The engine reconditioning incorporates the rectification, machining, replacement and control of all key elements to provide you with a marine engine block that can replace your old mechanics.

Repacked engine block in reverse HR before 1990 for GM V8 5 litres base with 12 attachment screws for intake pipe.

Characteristics :

- Rear spi of vilebrequin in 2 pieces

- 12 attachment screws for intake pipe

- Cache asbuteurs fixation extérieur

- 2 pinion kit for distribution (without chain)

Reverse rotation: ignition 1-2-7-5-6-3-4-8

- drilling for the gas pump axis

Perfect product for replacing your Crusader 305 -283, Chriscraft ,RIVA...

The engine reconditioning incorporates the rectification, machining, replacement and control of all key elements to provide you with a marine engine block that can replace your old mechanics.

Reconditioned engine block for base FORD 5 litres.

Characteristics :

- Flat powders

- Ignition order: 1-3-7-2-6-5-4-8

- Rear spi of vilebrequin in one piece

Perfect product for the replacement of your WTO engine, VOLVO, PCM ...

The engine reconditioning incorporates the rectification, machining, replacement and control of all key elements to provide you with a marine engine block that can replace your old mechanics.

Reconditioned engine block for GM V6 4.3 liters after 1990 type Vortec with 8 attachment screws for the intake pipe.

Characteristics :

- Rear vilebrequin joint one piece

- Plastic distribution box 6 screws

- Roller shaft

- Balance tree

- 8 attachment screws for intake pipe

- Cache culbuteurs fixation centre

Perfect product for replacing your 4.3GL engine, 4.3EFI ...

The engine reconditioning incorporates the rectification, machining, replacement and control of all key elements to provide you with a marine engine block that can replace your old mechanics.