DAM Marine offers a selection of layer pumps, some manuals and other automatics.If you have any questions about one of the bilge pumps we sell, don't hesitate to contact us directly.
Use of the hold pump
The bilge pump is used to promote the drying of your boat as long as a leak or damage occurs.There are several types of hold pumps...
Very robust construction in ABS, intended for intensive use on board professional ships.Resistant to corrosion and hydrocarbons."parabolic" room, allowing better water circulation, engine cooling and reduced consumption.
Power supply 24 volts.
Manual bilge pump.
Capacity 6840L/h
Connection 1-1/8
Livraison express
→
Tuesday 26 September
|
Livraison classique
→
Thursday 28 September
Very robust construction in ABS, intended for intensive use on board professional ships.Resistant to corrosion and hydrocarbons."parabolic" room, allowing better water circulation, engine cooling and reduced consumption.
Power supply 12 volts.
Manual bilge pump.
Capacity 6840L/h
Connection 1-1/8
Livraison express
→
Tuesday 26 September
|
Livraison classique
→
Thursday 28 September
Automatic start-up provided by a non-toxic and mercury-free floating contactor.
Protected motor against any water infiltration, particularly at the entrance of electrical cables and the engine axis.The engine is cooled by the flow of water generated by the propeller.
Capacity: 3100L/h
Connection: 1-1/8 - 29MM
Livraison express
→
Tuesday 26 September
|
Livraison classique
→
Thursday 28 September
The portable electric hold pump ATTWOOD is an immersed hold pump to remove the stagnant water from your hold.
Fully portable, this pump has a maximum refoulement height of 1m and can evacuate up to 900 litres per hour with new batteries.
It does not require electrical connections because it works with 3 D-format batteries (non-supplies).Its autonomy depends on the quality and condition of the batteries.For better autonomy, it is best to use alkaline batteries.
The installation of batteries is very easy by practicing a 1/4 turn.The storage is also very simple: just wrap the pipe around the body of the hold pump.
This portable hold pump comes with a 1 metre hose and a male connection.
Diameter: 130 mm
Height: 190 mm
Livraison express
→
Tuesday 26 September
|
Livraison classique
→
Thursday 28 September
Automatic start-up provided by a non-toxic and mercury-free floating contactor.
Protected motor against any water infiltration, particularly at the entrance of electrical cables and the engine axis.The engine is cooled by the flow of water generated by the propeller.
Automatic start-up provided by a non-toxic and mercury-free floating contactor.
Protected motor against any water infiltration, particularly at the entrance of electrical cables and the engine axis.The engine is cooled by the flow of water generated by the propeller.
The bilge pump is used to promote the drying of your boat as long as a leak or damage occurs.There are several types of hold pumps, some are manual, electric and others still electric and automatic.
\n\n
Manual hold pumps
\n
It can evacuate between 25 and 100L/min depending on the models and activate with the help of a mechanism, which you operate by movements of go and come thanks to a lever for example.These manual hold pumps are often used in addition to electric pumps, in case the electrical system fails.However, their low flow is that these manual bilge pumps will soon be overwhelmed on a water flow too large.
\n
One of the other alternatives to the manual bilge pump is the portable electric bilge pump, which can work with LR20 batteries, which can be used as a substitute for the manual bilge pump.
\n\n
Automatic hold pumps
\n
Also referred to as automatic bilge pumps emerrated as a result of their total waterproofing, they operate in 12V or 24V and are not greedy in electricity.These bilge pumps are running with the help of an ON/OFF switch, and are usually fixed to the lowest point and in difficult access areas, this positioning is facilitated by the low bulking of these bilge pumps.