MERCRUISER VM PUSH ROD
Push rod for Mercruiser diesel engine.
Stem with round tip.

Push rod for Mercruiser diesel engine.
Stem with round tip.
Plastic timing cover for Vortec V6 engine that does not have the hole for the crankshaft position sensor.
For mounting with the hole, refer to reference 500262.
Standard size piston for GM250 inline 6-cylinder engine.
Piston ring set for a Volvo Penta diesel engine cylinder of types:
AD31D-A, AD31L-A, AD31P-A, AD31XD
AD41D, AD41L-A, AD41P-A, D41D
D41L-A, KAD32P, KAD42A, KAD42B
KAD42P-A, KAD43P-A, KAMD42A, KAMD42B
KAMD42P-A, KAMD43P-A, TAMD31D, TAMD31L-A
TAMD31M-A, TAMD31P-A, TAMD31S-A, TAMD41D
TAMD42B, TAMD42WJ-A, TMD31D, TMD31L-A
TMD41D, TMD41L-A, TAMD41H-A, TAMD41H-B
TAMD41P-A, TAMD41M-A
Set of rings for a standard piston with dimensions 5/64 x 5/64 x 3/16
Complete cylinder kit for Volvo Penta 31 series engines and:
AD31
AD41A
AQAD31A
AQAD41A
D41A
TAMD31A
TAMD41A
TMD31A
TMD41A
Equipment to be used in addition to the 1542320 greaser not included.
Lower engine kit including all the gaskets for rebuilding a V6 engine with a 1-piece oil pan gasket.
Set of bearings for a 24mm wide connecting rod in standard size.
AQ105A, AQ115A, AQ115B
AQ130A, AQ130B, AQ130C, AQ130D
BB115A, BB115B, BB115C
MB20A, MB20B, MB20C
AQ120B, AQ125A, AQ140A
BB140A
AQ145A
BB145A
For block with 8 fixing screws for the crankshaft oil seal holder.
Set of bearings for a connecting rod in repair dimension 0.50mm.
Set of bearings for a Yanmar engine connecting rod in standard size.
Connecting rod bearings for a 24mm wide connecting rod in standard size on Volvo Penta B30 engines of types:
AQ165A
AQ170A, AQ170B, AQ170C
BB165A
BB170A, BB170B, BB170C
For block with 8 fixing screws for the crankshaft oil seal holder.
Existing material in width 27mm under reference 11054
Remanufactured connecting rod for GM 4 cylinder 3 liter engine.
Support moteur arrière pour moteurs yanmar série 2GM et 2YM15 disposant d'une embase saildrive SD20 - SD25.
Remarque sur le caoutchouc /gravé : 150
Charge maximale : 150kg
Complete fixing kit including washers, nut and threaded rod for SP171609 series engine mount
Thread types M16-1.5 X M20-1.5, length 150mm.
Kit to be used in combination with SP171609 series engine mounts with a diameter of M16-1.5 on the lower side (shim) and M20-1.5 on the upper side (top engine).
Axle kit not suitable for type 22323 supports (fine pitch).
Engine mount with the following dimensions:
Body diameter: 64 and 54mm
Body height: 40mm
Total height: 97mm
Threaded rod diameter: 12.8mm
Upper diameter: 64mm
Lower diameter: 53mm
Height: 39mm
male thread: 12.52mm
female thread: 8.28mm
Coupling for Mercruiser V6 - V8 engines with an Alpha One base.
Yanmar coupling diameter 190mm.
5 Springs
6 Mounting holes
26 Grooves
Complete distribution kit for 4 and 6 cylinder in-line engines based on GM181 GM153 GM250.
Complete timing belt kit for sheet metal timing case on 454 and 502 generation 4 and 5 engines.
Yanmar piston including segment, pin and two clips.
Compatible with 75mm bore engines:
- 1GM10
- 2GM20
- 3GM30