VETUS Fresh Water Systems – Comfort and hygiene onboard

This drinking water suction pipe can be installed on the top surface of almost any fixed tank with a maximum depth of 410 mm. Suitable for drinking water systems with a diameter of 13 mm.

WTKIT type connection kit for drinking water tank with inspection hatch and connectors.

Supplied with:

- An inspection hatch (WTIKIT)

- A right angle connector (RT38B) for the Ø 38 mm filling pipe

- A right angle connector (RT16B) for the Ø 16 mm water pump

- A right angle connector (RT16B) for ventilation Ø 16 mm

- Two fixing straps

- A T-piece to connect two Ø 16 mm tanks

WTKIT type connection kit for waste water only, please note not suitable for fuel tanks.

Complete with gasket and mounting flange.

Features :

Overall diameter (in mm): 156.

Diameter (in mm): 115.

To make opening and closing ILT120 lids easy and hassle-free.

A well-designed wrench to make moving stubborn lids easier.

Water heaters that are heated by engine coolant can supply their fresh water volume at temperatures above 90°C. In addition, it is often difficult and time-consuming to find the right temperature, which results in a loss of hot water.

Installing a thermostatic mixer prevents scalding and allows for easy adjustment of the correct temperature. This means less wasted hot water, a consistent temperature at the tap, and significant energy savings.

The mixer has a G½ thread. The temperature can be continuously adjusted between 30° and 70°C.

Trappe d'inspection pour eaux usées uniquement attention ne convient pas aux réservoirs de carburant.

Idéal pour les réservoirs métalliques.

Caractéristiques :

Diamètre de découpe (mm) : 115.

Diamètre (mm) : 156.

Electric heater with adjustable thermostat (40 - 80 ° C). External male thread, ISO 228/1 G1¼. The length of the screw-in element is 300 mm.

WHEL type heating elements meet low voltage requirements.

Features :

Volt (V): 230.

Watt (W): 500.

Electric heater with adjustable thermostat (40 - 80 ° C). External male thread, ISO 228/1 G1¼. The length of the screw-in element is 300 mm.

WHEL type heating elements meet low voltage requirements.

Features :

Volt (V): 230.

Watt (W): 1000.

Electric heater with adjustable thermostat (40 - 80 ° C). External male thread, ISO 228/1 G1¼. The length of the screw-in element is 300 mm.

WHEL type heating elements meet low voltage requirements.

Features :

Volt (V): 230.

Watt (W): 1500.

Electric heater with adjustable thermostat (40 - 80 ° C). External male thread, ISO 228/1 G1¼. The length of the screw-in element is 300 mm.

WHEL type heating elements meet low voltage requirements.

Features :

Volt (V): 120.

Watt (W): 1000.

Hole saw for plastic, GRP or stainless steel tanks with a diameter of 159 mm.

Tank gauge for drinking water, gasoline, and diesel. Indicates the difference in liquid level every 2.5 cm for maximum accuracy.

Each length of tube contains the maximum number of reed contacts (electronic switches),

instead of the absolute minimum of three (full, half full, empty). For this reason, your tank gauges

will be able to provide maximum accuracy. The contacts are sealed and "liquid-tight".

Technical characteristics:

• Empty 300?

• Full 10?

• For 12 and 24 volts

Features :

Voltage (V): 12/24.

Length (mm): 780.

Tank gauge for drinking water, gasoline, and diesel. Indicates the difference in liquid level every 2.5 cm for maximum accuracy.

Each length of tube contains the maximum number of reed contacts (electronic switches),

instead of the absolute minimum of three (full, half full, empty). For this reason, your tank gauges

will be able to provide maximum accuracy. The contacts are sealed and "liquid-tight".

Technical characteristics:

• Empty 300?

• Full 10?

• For 12 and 24 volts

Features :

Voltage (V): 12/24.

Length (mm): 680.

Tank gauge for drinking water, gasoline, and diesel. Indicates the difference in liquid level every 2.5 cm for maximum accuracy.

Each length of tube contains the maximum number of reed contacts (electronic switches),

instead of the absolute minimum of three (full, half full, empty). For this reason, your tank gauges

will be able to provide maximum accuracy. The contacts are sealed and "liquid-tight".

Technical characteristics:

• Empty 300?

• Full 10?

• For 12 and 24 volts

Features :

Voltage (V): 12/24.

Length (mm): 580.

Tank gauge for drinking water, gasoline, and diesel. Indicates the difference in liquid level every 2.5 cm for maximum accuracy.

Each length of tube contains the maximum number of reed contacts (electronic switches),

instead of the absolute minimum of three (full, half full, empty). For this reason, your tank gauges

will be able to provide maximum accuracy. The contacts are sealed and "liquid-tight".

Technical characteristics:

• Empty 300?

• Full 10?

• For 12 and 24 volts

Features :

Voltage (V): 12/24.

Length (mm): 480.

Tank gauge for drinking water, gasoline, and diesel. Indicates the difference in liquid level every 2.5 cm for maximum accuracy.

Each length of tube contains the maximum number of reed contacts (electronic switches),

instead of the absolute minimum of three (full, half full, empty). For this reason, your tank gauges

will be able to provide maximum accuracy. The contacts are sealed and "liquid-tight".

Technical characteristics:

• Empty 300?

• Full 10?

• For 12 and 24 volts

Features :

Voltage (V): 12/24.

Length (mm): 380.