Accessories for VETUS freshwater systems onboard

This drinking water suction pipe can be installed on the top surface of almost any fixed tank with a maximum depth of 410 mm. Suitable for drinking water systems with a diameter of 13 mm.

WTKIT type connection kit for drinking water tank with inspection hatch and connectors.

Supplied with:

- An inspection hatch (WTIKIT)

- A right angle connector (RT38B) for the Ø 38 mm filling pipe

- A right angle connector (RT16B) for the Ø 16 mm water pump

- A right angle connector (RT16B) for ventilation Ø 16 mm

- Two fixing straps

- A T-piece to connect two Ø 16 mm tanks

WTKIT type connection kit for waste water only, please note not suitable for fuel tanks.

Complete with gasket and mounting flange.

Features :

Overall diameter (in mm): 156.

Diameter (in mm): 115.

To make opening and closing ILT120 lids easy and hassle-free.

A well-designed wrench to make moving stubborn lids easier.

Water heaters that are heated by engine coolant can supply their fresh water volume at temperatures above 90°C. In addition, it is often difficult and time-consuming to find the right temperature, which results in a loss of hot water.

Installing a thermostatic mixer prevents scalding and allows for easy adjustment of the correct temperature. This means less wasted hot water, a consistent temperature at the tap, and significant energy savings.

The mixer has a G½ thread. The temperature can be continuously adjusted between 30° and 70°C.

Trappe d'inspection pour eaux usées uniquement attention ne convient pas aux réservoirs de carburant.

Idéal pour les réservoirs métalliques.

Caractéristiques :

Diamètre de découpe (mm) : 115.

Diamètre (mm) : 156.

Electric heater with adjustable thermostat (40 - 80 ° C). External male thread, ISO 228/1 G1¼. The length of the screw-in element is 300 mm.

WHEL type heating elements meet low voltage requirements.

Features :

Volt (V): 230.

Watt (W): 500.

Electric heater with adjustable thermostat (40 - 80 ° C). External male thread, ISO 228/1 G1¼. The length of the screw-in element is 300 mm.

WHEL type heating elements meet low voltage requirements.

Features :

Volt (V): 230.

Watt (W): 1000.

Electric heater with adjustable thermostat (40 - 80 ° C). External male thread, ISO 228/1 G1¼. The length of the screw-in element is 300 mm.

WHEL type heating elements meet low voltage requirements.

Features :

Volt (V): 230.

Watt (W): 1500.

Electric heater with adjustable thermostat (40 - 80 ° C). External male thread, ISO 228/1 G1¼. The length of the screw-in element is 300 mm.

WHEL type heating elements meet low voltage requirements.

Features :

Volt (V): 120.

Watt (W): 1000.

Hole saw for plastic, GRP or stainless steel tanks with a diameter of 159 mm.

Tank gauge for drinking water, gasoline, and diesel. Indicates the difference in liquid level every 2.5 cm for maximum accuracy.

Each length of tube contains the maximum number of reed contacts (electronic switches),

instead of the absolute minimum of three (full, half full, empty). For this reason, your tank gauges

will be able to provide maximum accuracy. The contacts are sealed and "liquid-tight".

Technical characteristics:

• Empty 300?

• Full 10?

• For 12 and 24 volts

Features :

Voltage (V): 12/24.

Length (mm): 780.

Tank gauge for drinking water, gasoline, and diesel. Indicates the difference in liquid level every 2.5 cm for maximum accuracy.

Each length of tube contains the maximum number of reed contacts (electronic switches),

instead of the absolute minimum of three (full, half full, empty). For this reason, your tank gauges

will be able to provide maximum accuracy. The contacts are sealed and "liquid-tight".

Technical characteristics:

• Empty 300?

• Full 10?

• For 12 and 24 volts

Features :

Voltage (V): 12/24.

Length (mm): 680.

Tank gauge for drinking water, gasoline, and diesel. Indicates the difference in liquid level every 2.5 cm for maximum accuracy.

Each length of tube contains the maximum number of reed contacts (electronic switches),

instead of the absolute minimum of three (full, half full, empty). For this reason, your tank gauges

will be able to provide maximum accuracy. The contacts are sealed and "liquid-tight".

Technical characteristics:

• Empty 300?

• Full 10?

• For 12 and 24 volts

Features :

Voltage (V): 12/24.

Length (mm): 580.

Tank gauge for drinking water, gasoline, and diesel. Indicates the difference in liquid level every 2.5 cm for maximum accuracy.

Each length of tube contains the maximum number of reed contacts (electronic switches),

instead of the absolute minimum of three (full, half full, empty). For this reason, your tank gauges

will be able to provide maximum accuracy. The contacts are sealed and "liquid-tight".

Technical characteristics:

• Empty 300?

• Full 10?

• For 12 and 24 volts

Features :

Voltage (V): 12/24.

Length (mm): 480.

Tank gauge for drinking water, gasoline, and diesel. Indicates the difference in liquid level every 2.5 cm for maximum accuracy.

Each length of tube contains the maximum number of reed contacts (electronic switches),

instead of the absolute minimum of three (full, half full, empty). For this reason, your tank gauges

will be able to provide maximum accuracy. The contacts are sealed and "liquid-tight".

Technical characteristics:

• Empty 300?

• Full 10?

• For 12 and 24 volts

Features :

Voltage (V): 12/24.

Length (mm): 380.

Keeping water fresh and preventing bacteria growth can be tricky, but a wide opening will help get the job done.

Periodic cleaning of all connections and of course the tank itself will be a much easier job if it can be done in a minimum of time.

Supplied with:

Fresh water filling connection Ø 38 mm.

Fresh water suction connection Ø 13 mm.

Ventilation connection Ø 16.

5-hole SAE flange tank level sensor connection.

Features :

Cutting diameter (mm): 159.

Diameter (mm): 120.

90 degree elbow filling connection Ø 38 mm for ILTCOND drinking water connection kit.

To make opening and closing ILT lids easy and hassle-free, a well-designed key to facilitate the movement of stubborn lids.

Tank gauge for drinking water, gasoline, and diesel. Indicates the difference in liquid level every 2.5 cm for maximum accuracy.

Each length of tube contains the maximum number of reed contacts (electronic switches),

instead of the absolute minimum of three (full, half full, empty). For this reason, your tank gauges

will be able to provide maximum accuracy. The contacts are sealed and "liquid-tight".

Technical characteristics:

• Empty 300?

• Full 10?

• For 12 and 24 volts

Features :

Voltage (V): 12/24.

Length (mm): 320.

Tank gauge for drinking water, gasoline, and diesel. Indicates the difference in liquid level every 2.5 cm for maximum accuracy.

Each length of tube contains the maximum number of reed contacts (electronic switches),

instead of the absolute minimum of three (full, half full, empty). For this reason, your tank gauges

will be able to provide maximum accuracy. The contacts are sealed and "liquid-tight".

Technical characteristics:

• Empty 300?

• Full 10?

• For 12 and 24 volts

Features :

Voltage (V): 12/24.

Length (mm): 280.

Trappe d'inspection innovant avec un design robuste. L'ILT est une trappe d'inspection innovante qui facilite l'ouverture, l'inspection et le nettoyage du réservoir, même après avoir été fermée pendant une longue période.

L'orifice d'inspection a une contre-bride et un caoutchouc de silicone qui sont insérés dans un trou de Ø 159 mm dans le réservoir. Convient aux réservoirs d'une épaisseur de paroi de 0.8 à 4 mm.

Il suffit de serrer les cinq boulons fournis qui compriment le caoutchouc de silicone pour assurer une étanchéité parfaite.

La conception "insérer - serrer" simplifie l'installation, ce qui rend le perçage d'un trou Ø 159 le plus dur de l'installation. La plaque aveugle noire peut être remplacée par divers kits de connexion.

Trappe d'inspection innovant avec un design robuste. L'ILT est une trappe d'inspection innovante qui facilite l'ouverture, l'inspection et le nettoyage du réservoir, même après avoir été fermée pendant une longue période.

L'orifice d'inspection a une contre-bride et un caoutchouc de silicone qui sont insérés dans un trou de Ø 159 mm dans le réservoir. Convient aux réservoirs d'une épaisseur de paroi de 4 à 10 mm.

Il suffit de serrer les cinq boulons fournis qui compriment le caoutchouc de silicone pour assurer une étanchéité parfaite.

La conception "insérer - serrer" simplifie l'installation, ce qui rend le perçage d'un trou Ø 159 le plus dur de l'installation. La plaque aveugle noire peut être remplacée par divers kits de connexion.