New VORTEC type engine block in reverse rotation RH for GM V8 5.7 liter base after 1990 with 8 fixing screws for the intake manifold.

Features :

- One-piece rear crankshaft oil seal

- 8 fixing screws for the intake pipe

- Central mounting rocker cover

- Reverse rotation: ignition 1-2-7-5-6-3-4-8

- No drilling hole for the fuel pump shaft

- VORTEC type cylinder heads

- Roller pushers

Perfect product for replacing your Mercruiser, Volvo, OMC , Crusader engine...

Engine block including the following positions:

- Timing case

- Oil pan

- Rocker cover

- Front damper

Reconditioned GM496 8.1 litre non-HO engine block.

This type of block is not in stock unlike HO bases, please contact us directly for any information.

Perfect product for replacing your Mercruiser, Volvo Penta engine

Engine reconditioning includes the grinding, machining, replacement and inspection of all key components to provide you with a marine engine block capable of replacing your old mechanics.

Reconditioned Mercruiser 383 MPI 350HP engine pack for Mercruiser base mounting.

All PLUS-SERIES engines are fully remanufactured. This is a genuine Mercury Marine OEM part that includes exhaust manifolds, electrical and ignition systems, so it is ready to be installed directly into a boat.

This 350HP engine has a flywheel Kilowatts of 261 with a maximum RPM (WOT) of 4800-5200 and a compression ratio of 9.0:1.

The recommended oil is Mercury MerCruiser Synthetic Blend 25W-40, rated NMMA FC-W with a fuel and ethanol tolerance of 87 octane / up to 10% ethanol.

MerCruiser 383 MPI 350HP Outboard Engine Systems:

- Engine control: ECM 555 with knock control and crankshaft trigger,

- Fuel supply: GEN II Cool Fuel with boost pump,

- Fuel injection: Multipoint electronic injection (MPI),

- Intake: Two-piece long-port intake with 75mm throttle body,

- Exhaust: Hot iron collector coated with electroplated paint with dry joint elbow,

- Water drainage: Multi-point drainage,

- Accessory drive: serpentine belt,

- Lubrication: 100 psi high flow oil pump.

Mercury Remanufacturing engines are backed by a one-year limited factory warranty.

New VORTEC type engine block for GM V8 5.7 litre base after 1990 with 8 fixing screws for the intake manifold.

Features :

- One-piece rear crankshaft oil seal

- 8 fixing screws for the intake pipe

- Centrally mounted rocker cover

- Standard rotation: ignition 1-8-4-3-6-5-7-2

- No drilling hole for the fuel pump shaft

- VORTEC type cylinder heads

- Roller pushers

Perfect product for replacing your Mercruiser, Volvo, OMC , Crusader engine...

Engine block including the following positions:

- Timing case

- Oil pan

- Rocker cover

- Front damper

Remanufactured engine block in standard rotation for GM V8 7.4 liter L29 base.

Features :

- One-piece rear crankshaft oil seal

- GM454 generation VI engine base

- Oval intake passages

- Standard rotation: ignition 1-8-4-3-6-5-7-2

- Roller pushers

- 6 fixing screws for the timing case

- L29 type cylinder heads (closed passages on the intake)

- 4 bolts per crankshaft bearing

Engine including:

- Rocker cover (G6 type aluminum)

- Sheet metal oil pan

- Timing case

- Front damper

- Intake and exhaust gaskets

Perfect product for replacing your Mercruiser, Volvo, Crusader engine

Engine reconditioning includes the grinding, machining, replacement and inspection of all key components to provide you with a marine engine block capable of replacing your old mechanics.

Engine including high quality internal parts to meet marine requirements.

Engine including high quality internal parts to meet marine requirements.

Brand new RH reverse rotation engine block for GM V8 5.7 litre base before 1990 with 12 intake manifold mounting screws.

Features :

- Two-piece rear crankshaft oil seal

- 12 fixing screws for the intake pipe

- Rocker cover external fixing

- Standard rotation: ignition 1-2-7-5-6-3-4-8

- Drilling for the fuel pump axle

Perfect product for replacing your Crusader, Mercruiser, Volvo, OMC engine...

Engine block including the following positions:

- Timing case

- Rocker covers

- Oil pan

- Front damper

Material on special order, please contact us for lead times.

Remanufactured engine block after 1990 for GM V8 7.4 liter base

Features :

- One-piece rear crankshaft oil seal

- GM454 generation VI engine base

- Oval intake passages

- Standard rotation: ignition 1-8-4-3-6-5-7-2

- Roller pushers

- 4 bolts per crankshaft bearing

- 6 fixing screws for the timing case.

- Cylinder heads with a central bore in the middle of the intake (NOT L29)

We usually replace MARK V engine bases with flat tappets with MARK VI with roller tappets.

Perfect product for replacing your Mercruiser, Volvo, Crusader engine.

Engine reconditioning includes the grinding, machining, replacement and inspection of all key components to provide you with a marine engine block capable of replacing your old mechanics.