Lever ratchet chain stop for 8mm to 10mm chain, for RC8 windlass series.

Windlasses are not designed to withstand the high loads that can be transmitted by the chain when at anchor. The chain must be secured with a chain stopper or the cable must be secured to a cleat, bollard, or other load-bearing point.

Height matched to the chain level of the RC series windlasses, meaning no packer or base is required. The body and pin are made of 316 stainless steel and the pawl is made of high-strength 2205 stainless steel.

The ratchet is shaped to fit the chain, preventing damage to the galvanizing caused by traditional ratchets. It has a high-quality, mirror-polished finish.

Compact and economical chain stop for 8 to 10 mm chains. This stainless steel model prevents damage to the windlass drive mechanism.

Chain stoppers hold the chain and relieve the load on the windlass. Always use a chain stopper to secure and raise the anchor, to release the anchor, or to prevent the anchor from accidentally falling free while underway.

Remote control only for AA730 HHR.

AA342 Dual Windlass Controller.

For use with windlasses, davits, thrusters, and other marine equipment. AA341 General Dual Equipment Controller.

Electrical protection against counter-electromotive force.

Made with a rubber overmold for impact protection and optimal grip. Storage cradle.

Works in parallel with any AutoAnchorâ"¢ product, rocker switches, foot switches, or other control equipment. Connectable to DC, AC, and hydraulic systems.

Heavy duty 4.5m coiled cable and connectors.

All products are IP67 rated, including cables, plugs and sockets.

For use with windlasses, davits, thrusters, and other marine equipment. AA341 General Dual Equipment Controller.

Electrical protection against counter-electromotive force.

Made with a rubber overmold for impact protection and optimal grip. Storage cradle.

Works in parallel with any AutoAnchorâ"¢ product, rocker switches, foot switches, or other control equipment. Connectable to DC, AC, and hydraulic systems.

Heavy duty 4.5m coiled cable and connectors.

All products are IP67 rated, including cables, plugs and sockets.

Use for windlasses, davits, thrusters and other marine equipment.

Electrical protection against counter-electromotive force.

Made with a rubber overmold for impact protection and optimal grip. Storage cradle.

Works in parallel with any AutoAnchorâ"¢ product, rocker switches, foot switches, or other control equipment. Connectable to DC, AC, and hydraulic systems.

Heavy duty 4.5m coiled cable and connectors.

All products are IP67 rated, including cables, plugs and sockets. Bridge socket with 2m flying lead reducing the risk of corrosion (except AA320 series)

Heavy-duty solenoids for RC12 Series dual-direction windlasses are used in conjunction with the remote up/down panel, AutoAnchorâ"¢ rod counters, mobile handheld remotes and/or foot switches to switch the motor in the required direction.

They are suitable for our winch motors. Available in 24V DC for 2-terminal permanent magnet (PM), 3-terminal series-wound (SW) and 4-terminal field-wound (FW) motors.

Ignition-protected solenoids. Installation in a dry location is always recommended.

Heavy-duty solenoids for the RC8-8 RC10 and RC12 series dual-direction windlasses are used in conjunction with the remote up/down panel, AutoAnchorâ"¢ rod counters, mobile handheld remotes and/or foot switches to switch the motor in the required direction.

They are suitable for our winch motors. Available in 24V DC for 2-terminal permanent magnet (PM), 3-terminal series-wound (SW) and 4-terminal field-wound (FW) motors.

Ignition-protected solenoids. Installation in a dry location is always recommended.

Heavy-duty solenoids for the RC8-8 RC10 and RC12 series dual-direction windlasses are used in conjunction with the remote up/down panel, AutoAnchorâ"¢ rod counters, mobile handheld remotes and/or foot switches to switch the motor in the required direction.

They are suitable for our winch motors. Available in 12V DC for 2-terminal permanent magnet (PM), 3-terminal series-wound (SW) and 4-terminal field-wound (FW) motors.

Ignition-protected solenoids. Installation in a dry location is always recommended.

Heavy-duty solenoids for the RC6 and RC8-6 Series dual-direction windlasses are used in conjunction with the remote up/down panel, AutoAnchorâ"¢ rod counters, mobile handheld remotes and/or foot switches to switch the motor in the required direction.

They are suitable for our winch motors. Available in 24V DC for 2-terminal permanent magnet (PM), 3-terminal series-wound (SW) and 4-terminal field-wound (FW) motors.

Ignition-protected solenoids. Installation in a dry location is always recommended.

Heavy-duty solenoids for the RC6 and RC8-6 Series dual-direction windlasses are used in conjunction with the remote up/down panel, AutoAnchorâ"¢ rod counters, mobile handheld remotes and/or foot switches to switch the motor in the required direction.

They are suitable for our winch motors. Available in 12V DC for 2-terminal permanent magnet (PM), 3-terminal series-wound (SW) and 4-terminal field-wound (FW) motors.

Ignition-protected solenoids. Installation in a dry location is always recommended.

One-way solenoids should be used when only one-way motor rotation is required. For example, capstan winches.

Features :

Single/Double Relay: Single.

Voltage (V): 24.

One-way solenoids should be used when only one-way motor rotation is required. For example, capstan winches.

Features :

Single/Double Relay: Single.

Voltage (V): 12.

This robust and durable unit, made of black synthetic material, is weather-resistant and features a UV-stabilized waterproof diaphragm. Its current draw capacity is 150A.

Supplied with assembly instructions and screws.

This robust unit, which has a durable, weather-resistant, white polyethylene cover, is equipped with a UV-stabilized, waterproof diaphragm and has a current draw capacity of 150A.

Supplied with assembly instructions and screws.

This robust unit, which has a durable, black polyethylene cover, is weather-resistant and has a UV-stabilized waterproof diaphragm. Its current draw capacity is 150A.

Supplied with assembly instructions and screws.

This robust and durable unit made of stainless steel (AISI 316) is weather-resistant and features a UV-stabilized waterproof diaphragm. Its current draw capacity is 150A.

Supplied with assembly instructions and screws.

40A - 48V circuit breaker for protecting the main conductor circuit of DC winches and the control circuit of hydraulic winches.

Compact foot switch made of polyamide and nylon with black cover.

Operates via solenoids, allowing for smaller diameter wiring. 5 hours maximum current draw capacity.

Compact foot switch made of polyamide and nylon with white cover.

Operates via solenoids, allowing for smaller diameter wiring. 5 hours maximum current draw capacity.

Easy-to-use, panel-mounted up/down switch for remote windlass control from the helm station, flybridge, or cockpit. Includes an on/off switch and a power indicator light.

Suitable for use with bi-directional solenoids.

Made from marine grade, splash resistant materials.

Suitable for use on 12 and 24 volts DC.

70A - 12/24V circuit breaker for protecting the main conductor circuit of DC winches and the control circuit of hydraulic winches.

Compatible with HRC-8 windlass series.

135A - 12/24V circuit breaker for protecting the main conductor circuit of DC winches and the control circuit of hydraulic winches.

Compatible with windlass series 800 to 3500 12V and 4000 24V