Exhaust temperature alarm probe, two probes available for VETUS mounting.

Use the XHSM sensor in VETUS waterlocks with a pre-installed connection.

Use the XHSH type sensor for mounting in the exhaust pipe

Note: Temperature sensors and alarm unit must be ordered separately. In the case of a

twin-engine installation, 2 sensors can be connected to one alarm unit.

Suitable for exhaust pipe with internal diameter of Ø 50 mm.

The gooseneck raises the exhaust line above the waterline and provides additional reduction of the

noise. The outlet fits directly onto all VETUS rubber exhaust outlets.

Features :

Water inlet pipe connection diameter (mm): 50.

Outlet pipe connection diameter (mm): 50.

Length (mm): 182.

Width (mm): 135.

Height (mm): 502.

Anti-siphon elbow without valve and with hose. Supplied with ventilation pipe, connection 13 - 32 mm.

Can be used as a drainage system or toilet.

Interchangeable with the AIRVENT type and have the same fixing center distances.

Comes complete with fitting, hose clamps and 2m of hose. Non-valve anti-siphon elbows must be fitted with a ventilation pipe.

The air vent fitting rotates 360°. (Includes a 2 m hose and skin fittings). In addition, the valve can be serviced without removing the vent from the wall and no tools are required for this. For replacement, a set of 5 valves is available as a spare part.

A 13 mm diameter flexible hose can be directly connected to the elbow connections

Can be connected to pipes with inner diameters of 13, 19, 25 and 32 mm.

Size :

Width (mm): 68.

Length (mm): 96.

Height (mm): 133.

The VETUS gas/water separator has a dual function. It separates the injected raw cooling water from the exhaust gases and also functions as a gooseneck. Particularly important for generator sets, the separator reduces exhaust noise and discharges the cooling water below the waterline, thus avoiding the characteristic splashing noise.

Features :

360º rotating pipe fittings for 75mm internal pipe diameters

50mm cooling water drain

Comes with a stainless steel (AISI 316) mounting bracket with synthetic straps

Combined with a silencer, the gooseneck saves installation time and space while maintaining the essential qualities of a good exhaust system with incredibly negligible back pressure. Prevents water from backing up the exhaust.

Suitable for pipes with an internal diameter of Ø 75 mm.

*Interchangeable connector for 65 mm hose (SET00025) available separately.

Fully rotating sections and pipe fittings ensure easy installation. Comes with a pipe fitting to connect the ventilation.

Features :

Capacity (liters): 10.

Length (mm): 285.3.

Width (mm): 160.

Height (mm): 646.4.

Airlock position: Vertical.

% Noise Reduction: 25.

Once your boat's engine has been stopped, with the correct volume capacity selected, the VETUS waterlock will ensure that water does not return to the engine. All VETUS water pots are equipped with a drain plug for winter storage.

Suitable for exhaust pipes with an inner diameter of Ø 45 mm.

Capacity: 4.3L

A: 372 x 110 mm

B: 211mm

D: 45mm

1 adjustable entrance

1 fixed output

Manufactured from the specially blended NAVIDURIN® composite, heat-resistant up to 260°C. The same applies to thermal resistance to deformation under pressure. The HPW series is ideal for applications where the system is put to the test, such as commercial vessels or coast guards. This ability to handle extreme conditions, combined with the rotating bodies and pipe fittings, makes the HPW series a cost-effective alternative to expensive, high-end custom solutions.

It has a 360º rotating body and allows for infinite connection of hose fittings. It comes with floor mounting brackets. Large capacity water lifter provides complete safety for your engine. Excellent noise attenuation with minimal back pressure.

Features :

Capacity (liters): 55.

Water inlet pipe connection diameter (mm): 127.

Outlet pipe connection diameter (mm): 152.

Length (mm): 950.

Width (mm): 440.

Height (mm): 648.

Airlock position: Vertical.

% Noise Reduction: 30.