Pressure flange dimensions:

Exterior 134mm

Interior 73.66

Oil dipstick for Borg Warner - Velvet Drive series 71 and 72 inverter.

Brown oil dipstick for PCM inverter type IRM80A with engraving 3201201016.

Oil cooler for Volvo Penta D4 and D6 engines as a replacement for MOTA brand coolers but at a significantly lower cost.

Cooler with the same thermal characteristics but with a simpler architecture.

Retrofit cooling kit providing better cooling than the original Volvo coolers.

The presence of a larger number of bundles increases the cooling capacity.

Much more economical material than the original Volvo material.

Hardware including installation kit.

Complete gasket kit for the Velvet Drive brand V-drive series 71 and 72.

Connecting joint between the Chriscraft 283 engine block and the Paragon inverter.

Complete repair kit including seals and discs for Hurth ZF series 20 - 25 - 220 - 250 reverse gear.

- 10 bronze friction discs

- 8 steel friction discs

- Complete seal kit

Complete IRM80 inverter kit for PCM type FORD engine with a ratio of 1.23/1.

The IRM40 type inverters are now replaced by more robust IRM80 series inverters.

Kit including the following positions:

- Inverter

- Oil cooler

- Flexible

- Coupling

- Mounting kit

Complete disc kit for Paragon brand inverter types:

- HF7 DIRECT - right output

- P21 ratio 1:1

- P22 ratio 1.5:1

- P23 ratio 2.04:1

- P24 ratio 2.52:1

- P25 ratio 3.00:1

P300 / P31 series ratio 1:1

Kit including 6 bronze discs, 7 metal discs, circlips.

For a non-direct Paragon HF7 inverter, refer to reference ALT750J

Complete friction disc kit for Velvet Drive - Borg Warner 72 series inverter.

Kit including the following positions:

- 6 small steel forward discs .068

- 7 small bronze discs .060

- 1 front pressure disc

- 1 rear pressure disc

Complete repair kit for Hurth HBW 5 - 50 and 100 inverter including:

- 8 bronze discs .063

- 6 .056 steel discs

IRM80 PCM reversor with a ratio of 1.1/1 and a mechanical inversion control.

Planned mounting for PCM type V-DRIVE.

Clutch cone for Yanmar KM2P reverse gear.

Diameter: 67.8mm

Height: 43mm

PCM brand inverter type IRM80 with a ratio of 1.1/1 and an electric inversion control.

Installation intended for PCM type V-DRIVE.

Complete inverter from Velvet Drive - Borg Warner type 71C with a ratio of 1/1.

GM small block application.

Complete replacement kit for ZF electric inverter 45 series with a ratio of 1:1 by a Velvet Drive brand inverter of the same characteristics and size.

Original INDMAR replacement.

Assembly for inverters with an electric selector for changing from forward to reverse gear.

Electric reverse gear.

Kit including:

- reassembly/screws kits.

- Jiffy type oil hose.

ZF brand inverter series 30 with straight output allowing the replacement of KBW inverters.

Ratio 2.70.

SAE4 flange for mounting on Yanmar turbo engines of types: 4JH4-TE - 4JH80 - 4JH110.

When replacing a Kanzaki brand Yanmar reverse gear with a ZF reverse gear it is necessary to also replace the coupling using part number 129673-81250.

Reversing support plate for PCM V-DRIVE inverter.

Yanmar reverse gear oil dipstick.

Tube length: 18cm.

Oil cooler for Yanmar engine with ZF inverter.

Total length: 360mm

Body Length: 260mm

Body diameter: 75mm

Hose diameter: 45mm

Connection: 3/8 - 9.5mm NPT