Protective products for cars, boats, motorcycles, etc.

RejeX® is a thin-film polymer coating designed to provide a high-release protective finish for vehicles of all types.

This very thin film - less than one micron thick - prevents staining and adhesion of common contaminants such as exhaust fumes, insects, oil, tree sap, bird droppings, road grime, brake dust, etc.

NOTHING STICKS BUT SHINE!™

It's easy to apply and produces a deep, glossy shine that lasts for months.

RejeX does not contain any of the oils found in some other products known to contaminate paint and cause problems.

REJEX APPLICATION

Ideally, apply RejeX to a fresh, dry, clean surface.

When temperatures exceed 85°F, be sure to apply RejeX away from sunlight.

If the surface is too hot, the coating may harden before it has properly bonded to the surface, so it may not perform to its potential.

Let dry for about 20 minutes, wipe dry, then let dry for 8-12 hours (depending on humidity - the higher the humidity, the faster the cure).

Curing is necessary to allow the monomers (polymer building blocks) that make up RejeX to attach to the treated surface and bond into a clear, waterproof film.

It is important to allow RejeX to dry for 8 to 12 hours.

If the coating is exposed to contaminants such as oil, fuel, soot, hard water, tree sap, cleaning products, etc. before it has cured, the contaminants may interfere with or embed the protective film.

REJEX PROTECTS AND BEAUTIFIES PAINTED METAL, GLASS, ACRYLIC, GEL COAT, FIBERGLASS, GLOSSY PLASTIC AND POLISHED METAL SURFACES

RejeX is not intended for use on porous surfaces, heavily oxidized painted surfaces, or to fill fine scratches.

RejeX can be applied in multiple coats, allowing 8 hours of cure time between coats for deeper color and greater depth of gloss.

RejeX has a higher refractive index than waxes, so it produces richer, deeper colors and a long-lasting glossy finish.

RejeX can be used over existing wax - however, the duration of protection will be reduced as the underlying wax degrades more quickly.

There is no reason to wax RejeX. As mentioned before, RejeX leaves a shinier and more durable finish than wax… If a RejeX-treated surface needs repainting, normal paint preparation is all that is required.

Abrasive cleaners, polishes, rubbing compounds, and some chemical strippers may remove RejeX.

Grease for mounting cooling turbines.

Packaging: 20 gram tube.

PERMATEX Red RTV High Temp Joint Compound

Silicone sealant formulated for high temperature applications or heavy duty use.

Ideal for replacing almost any gasket that resists cracking, shrinking and migration caused by thermal cycling.

Suitable for marine and automotive use: exhaust, turbo, intake manifold, etc.

Intermittent temperature range: -54°C to 343°C (-65°F to 650°F).

Seal color: orange-red.

85 gram (3 OZ) tube.

Quicksilver outperforms automotive gear oil in marine applications due to special marine gear additives.

Continued use of this base lubricant will ensure:

• Maximum protection against excessive wear - even in the presence of water

• Prevents corrosion and pitting

• Helps extend the life of the base

60 liter barrel.

75W140 synthetic gear oil API-GL5 standard for Volvo Penta gear types:

- DPH RATIO 1.59:1 example D6-400

- DP-G example KAD300

Packaging 1 liter.

MOTUL LR MULTI is a ready-to-use coolant made from monoethylene glycol, using a mixed organic and inorganic technology called hybrid additives. Compatible with all monoethylene glycol-based coolants. Ideal for topping up.

Recommended for gasoline and diesel engine cooling circuits.

Packaging in 5 liter cans.

Manual transfer pump, length 1.70 m

The simplest and most efficient system for transferring all liquids without energy

Suitable for use with: diesel, kerosene, cleaning products, sea water, thinners and alcohols.